China Professional CHINAMFG Double Acting High Pressure Nitrogen Gas Booster & Compressors Unit air compressor for sale

Product Description

Product Description

The CHINAMFG gas booster equipment uses pure compressed air as the driving power source, gas booster pump as the pressure source, and Hydrogen, Nitrogen, Oxygen, Helium, N2O, Argon, CO2 and other gases as the pressurized medium. The output pressure is proportional to the driving gas pressure.

 

By adjusting the pressure of the driving gas source, the corresponding pressure of the pressurized gas can be obtained. When the pressure of the driving gas source is balanced with that of the pressurized gas, the pneumatic booster pump will be automatically stops and the output gas pressure is stabilized at the preset pressure. Therefore, it has the features of explosion-proof, energy saving, environmental protection, adjustable output pressure, small volume, light weight, simple operation, reliable performance and wide application range.

 

To operate this system, the drive gas from the air compressor is required to start the CHINAMFG booster pump. The pressure of the drive gas can be adjusted by valves and pressure gauges. And the output gas pressure can be adjusted.The expected working pressure can be achieved by adjusting the pressure of the drive inlet. When the driving air pressure and the output pressure are balance, the pump stops filling pressure and the output pressure remains at the preset value.

 

TEREK gas booster pump uses compressed air to drive large area end piston to small area end to get high pressure gas output. The equipment can be used for compressed air and other gas, the output pressure can be adjusted by inlet valve. The output can ensure gas is not contaminated. Automatic pressure maintaining. Driven by gas, No spark or Flame and No generating heat, Can use it in dangerous places.
 

Product Parameters

Basically, the principle of operation is similar to a reciprocating amplifier where control of the piston at the end position is reciprocating. The automatic reciprocating motion of the piston is controlled by a built-in four-way valve.
TEREK pumps are air driven at a drive air pressure of 3 to 8 bar (29 to 116 psi) by the normal air compressor. 

Refer to model technical parameters.

Product name

Pneumatic air driven gas booster pump pressurized transfer and filling equipment.

Model

GU-GTC-40

Pressure ratio

40:1

Drive air source pressure

3-8 bar.

Maximum outlet pressure

320 bar (46400 psi)

When the driven air pressure is 5.0 bar

High pressure outlet pressure is 200 bar.

When the driven air pressure is 6.0 bar

High pressure outlet pressure is 240 bar.

Min gas inlet pressure

15 bar

Max gas inlet pressure

320 bar

Outlet pressure control unit

Drive air regulator valve

Power source

TEREK gas booster pump

Pressure control accuracy

Less than 1%F.S;

Pressure measurement accuracy

0.4 pressure gauge

Valves and piping

High pressure needle valve and stainless steel piping

Weight

38 KG

Export wooden case weight

45 KG

Equipment dimension

580*450*570 mm

Packing size

610*500*600 mm

Packing specifications

Standard export wooden case

Connection size(inch) Gas inlet

NPT1/4

Connection size(inch) Gas outlet

NPT1/4

Production time

12-15 working days.

System configuration:

TEREK gas booster pump uses compressed air to drive large area end piston to small area end to get high pressure gas output. It can be used for compressed air and other gas. The output pressure can be adjusted by inlet valve. The output can ensure gas is not contaminated. Automatic pressure maintaining. Driven by gas, No spark or Flame and No generating heat, Can use it in dangerous places.

GU-GTC series gas booster unit control cabinet mainly includes 1 set of GTC series air-driven gas booster pump, pressure gauges, air filter, gas inlet filter, control valves, air regulating valve, pipelines, cabinet, and pressure release valve etc.

The diameter of the drive cylinder: 160mm

Drive cylinder stroke: 100mm        

High pressure cylinder stroke: 100mm

The maximum driving pressure of the drive air is 8 bar / 116 psi.

 

Detailed Images

Product advantages

 

1. All pipes and fittings are made of stainless steel to ensure a long life

2. The pump will stop working automatically when the output pressure reaches the preset value

3. Maintain long working hours with no energy expenditure

4. No dissipated heat during the pressure holding phase

5. No risk for explosion and spark in oil and gas field

6. The pump will start automatically when the outlet pressure drops slightly or the air drive pressure increases.

7. The working pressure can be adjusted by adjusting the pressure of the driven air.
8. Easy to install, move, use and maintain

Application Fields

1. Pressure test with gas

2. Gas transfer and filling(Argon/Helium/Hydrogen/Oxygen/Nitrogen/CO2/NO2/CH4/LNG/LPG/CNG/FM200 etc.)

3. Charging of gas cylinder and accumulator with nitrogen

4. Supply for isolating gas systems

5. High pressure gas injection system for various industries

6. Transfer of oxygen cylinders

7. Charging of breathing air bottles

8. Leak test

9. Hydrostatic testing for valves, tanks, pressure vessels, pressure switches, hoses, pipes and tubing, pressure gauges, cylinders, transducers, well casings, gas bottles and air craft components

Packaging & Shipping

 

Our Services

1. We’d like to provide our professional advice regarding machines, materials, packing and market for this product.

2. We’d like to customize special machine according to customer’s request.

3. We’d like to help our customers for booking ship as customer request.

5. Operation manual will be provided after shipment.

6. We provide 1 year warranty.

7. Free wearing parts will be sent together with the machine.

8. Working video of the machine will be sent to you accordingly to your need.

All equipment and accessories are guaranteed for 1 year. Our sales staff and technical department provide permanent technical advice and operation guidance. If you have any questions about the operation of the equipment, please turn off the air source and equipment, check the instructions in time or contact the sales and service personnel. Thanks.
 

Equipment inventory and workshop

Company Information:

TEREK company focus on high pressure fluid transfer all the time and supply perfect high pressure fluid transfer solution and service. Supplying high-quality product and service is the CHINAMFG aim of TEREK.
As the experienced manufacturer of industrial booster pump, the technology of air driven booster pump and pressurization system reach to a good level. It can pressurize most liquid, such as oil, water, corrosive liquid and chemical liquid applications. High quality seals, long service life available.
Based on the high quality of our products, reasonable prices and excellent after-sales service, we have gained a high reputation in this field of fluid pressure control equipment.

Our main products including: 
Pneumatic Gas/Liquid Booster Pumps.
Refrigerant booster pump and air amplifier.
Fluid pressurized hydrostatic hydraulic pressure test equipment or high pressure chemical fluid injection equipment.
High pressure oxygen, hydrogen, nitrogen, argon, Helium, N2O, CO2 or other gas pressurized transfer refilling equipment or gas injection equipment.
Pneumatic pump glycerin oil pressurized injection equipment.
LPG / Propane and butane pressurized transfer filling station equipment.
Pipe/tube/valve/cylinder/brake pipe, automobile pipe, aircraft hydraulic pipe, pressure vessels hydraulic pressure test machine(Computer control or manual control or Intelligent digital display instrument).
MCU Intelligent digital display instrument pneumatic gas booster pump system leak test bench.
Computer control / Intelligent instrument control safety relief valve PSV test bench.
Portable safety valve test clamping table and test equipment.
Online safety valve test instrument equipment.

FAQ:

1.Q : Are you manufacturer ?

A: Yes, We are the manufacturer with continuous and improved R&D. Production, Quality Check and service supply.

2.Q : Can I get your price list ?

A: Yes, Sure. In order to send you our available offered price. Please choose the products and let us know the product model and requirement in detail.

3.Q : Do you have stock for all items?

A:In general, we have some stock, while if you need a bulk order, we still need time to produce it. Of course, we will inform all details you before your payment.

4.Q : What is payment terms ?

A: Sample order : 100% full payment before start to production;

Large order : 30% deposit first, 70% pay after see the BL copy ;

5.Q: Can give free sample ?

A : Free : if small spare parts and the cost not too much is ok ;

Not Free : the cost expensive and all the machine can not be free ;

6.Q : How long can be finished the goods ?

Delivery date: 10-15 working days after deposit paid

Two years warranty, when the products reach to destination.

/* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service: Technical Support and Services
Warranty: 24 Months
Max.Head: >150m
Max.Capacity: >400 L/min
Pressure Medium: Gas
Type: Reciprocating Pump
Customization:
Available

|

air compressor

How Do You Troubleshoot Common Issues with Gas Air Compressors?

Troubleshooting common issues with gas air compressors involves identifying and addressing potential problems that may arise during operation. Here’s a detailed explanation of the troubleshooting process:

1. Start with Safety Precautions:

Prior to troubleshooting, ensure that the gas air compressor is turned off and disconnected from the power source. Follow proper safety procedures, such as wearing appropriate personal protective equipment (PPE), to avoid accidents or injuries.

2. Check Power Supply and Connections:

Verify that the compressor is receiving power and that all electrical connections are secure. Inspect the power cord, plug, and any switches or controls to ensure they are functioning properly. If the compressor is equipped with a battery, check its charge level and connections.

3. Check Fuel Supply:

For gas air compressors that use gasoline or propane, ensure that there is an adequate fuel supply. Check the fuel tank level and verify that the fuel shut-off valve is open. If the compressor has been sitting idle for an extended period, old or stale fuel may cause starting issues. Consider draining and replacing the fuel if necessary.

4. Inspect Air Filters:

Dirty or clogged air filters can restrict airflow and affect the compressor’s performance. Check the intake air filters and clean or replace them as needed. Clogged filters can be cleaned with compressed air or washed with mild detergent and water, depending on the type of filter.

5. Check Oil Level and Quality:

If the gas air compressor has an engine with an oil reservoir, verify the oil level using the dipstick or oil level indicator. Insufficient oil can lead to engine damage or poor performance. Additionally, check the oil quality to ensure it is clean and within the recommended viscosity range. If needed, change the oil following the manufacturer’s guidelines.

6. Inspect Spark Plug:

If the gas air compressor uses a spark plug ignition system, inspect the spark plug for signs of damage or fouling. Clean or replace the spark plug if necessary, following the manufacturer’s recommendations for gap setting and torque.

7. Check Belts and Pulleys:

Inspect the belts and pulleys that drive the compressor pump. Loose or worn belts can cause slippage and affect the compressor’s performance. Tighten or replace any damaged belts, and ensure that the pulleys are properly aligned.

8. Listen for Unusual Noises:

During operation, listen for any unusual or excessive noises, such as grinding, rattling, or squealing sounds. Unusual noises could indicate mechanical issues, loose components, or improper lubrication. If identified, consult the compressor’s manual or contact a qualified technician for further inspection and repair.

9. Consult the Owner’s Manual:

If troubleshooting steps do not resolve the issue, refer to the compressor’s owner’s manual for specific troubleshooting guidance. The manual may provide additional troubleshooting steps, diagnostic charts, or recommended maintenance procedures.

10. Seek Professional Assistance:

If the issue persists or if you are unsure about performing further troubleshooting steps, it is recommended to seek assistance from a qualified technician or contact the manufacturer’s customer support for guidance.

Remember to always prioritize safety and follow proper maintenance practices to prevent issues and ensure the reliable performance of the gas air compressor.

air compressor

What Is the Impact of Altitude on Gas Air Compressor Performance?

Altitude can have a significant impact on the performance of gas air compressors. Here’s a detailed explanation:

1. Decreased Air Density:

As altitude increases, the air density decreases. This reduction in air density affects the performance of gas air compressors, primarily because compressors rely on the intake of ambient air to generate compressed air. With lower air density at higher altitudes, the compressor’s ability to draw in a sufficient volume of air is reduced.

2. Reduced Compressor Output:

The decrease in air density directly affects the compressor’s output. Gas air compressors may experience a decrease in their maximum airflow and pressure capabilities at higher altitudes. This reduction in output can impact the compressor’s efficiency and its ability to deliver the required compressed air for various applications.

3. Increased Compressor Workload:

At higher altitudes, gas air compressors need to work harder to maintain the desired level of compressed air output. The reduced air density means the compressor must compress a larger volume of air to achieve the same pressure as it would at lower altitudes. This increased workload can lead to higher energy consumption, increased wear and tear on the compressor components, and potentially decreased overall performance and lifespan.

4. Engine Power Loss:

If the gas air compressor is powered by an internal combustion engine (such as gasoline or diesel), altitude can also impact the engine’s performance. As the air density decreases, the engine may experience a power loss due to reduced oxygen availability for combustion. This can result in reduced engine horsepower and torque, affecting the compressor’s ability to generate compressed air.

5. Considerations for Proper Sizing:

When selecting a gas air compressor for use at higher altitudes, it is crucial to consider the specific altitude conditions and adjust the compressor’s size and capacity accordingly. Choosing a compressor with a higher airflow and pressure rating than required at sea level can help compensate for the reduced performance at higher altitudes.

6. Maintenance and Adjustments:

Regular maintenance and adjustments are necessary to optimize the performance of gas air compressors operating at higher altitudes. This includes monitoring and adjusting the compressor’s intake systems, fuel-to-air ratio, and ignition timing to account for the reduced air density and maintain proper combustion efficiency.

In summary, altitude has a notable impact on the performance of gas air compressors. The decrease in air density at higher altitudes leads to reduced compressor output, increased compressor workload, potential engine power loss, and considerations for proper sizing and maintenance. Understanding these effects is crucial for selecting and operating gas air compressors effectively in various altitude conditions.

air compressor

Can Gas Air Compressors Be Used in Remote Locations?

Yes, gas air compressors are well-suited for use in remote locations where access to electricity may be limited or unavailable. Their portability and reliance on gas engines make them an ideal choice for providing a reliable source of compressed air in such environments. Here’s a detailed explanation of how gas air compressors can be used in remote locations:

1. Independence from Electrical Grid:

Gas air compressors do not require a direct connection to the electrical grid, unlike electric air compressors. This independence from the electrical grid allows gas air compressors to be used in remote locations, such as wilderness areas, remote job sites, or off-grid locations, where it may be impractical or cost-prohibitive to establish electrical infrastructure.

2. Mobility and Portability:

Gas air compressors are designed to be portable and easy to transport. They are often equipped with handles, wheels, or trailers, making them suitable for remote locations. The gas engine powering the compressor provides mobility, allowing the compressor to be moved to different areas within the remote location as needed.

3. Fuel Versatility:

Gas air compressors can be fueled by various types of combustible gases, including gasoline, diesel, natural gas, or propane. This fuel versatility ensures that gas air compressors can adapt to the available fuel sources in remote locations. For example, if gasoline or diesel is readily available, the gas air compressor can be fueled with these fuels. Similarly, if natural gas or propane is accessible, the compressor can be configured to run on these gases.

4. On-Site Power Generation:

In remote locations where electricity is limited, gas air compressors can serve as on-site power generators. They can power not only the compressor itself but also other equipment or tools that require electricity for operation. This versatility makes gas air compressors useful for a wide range of applications in remote locations, such as powering lights, tools, communication devices, or small appliances.

5. Off-Grid Operations:

Gas air compressors enable off-grid operations, allowing tasks and activities to be carried out in remote locations without relying on external power sources. This is particularly valuable in industries such as mining, oil and gas exploration, forestry, or construction, where operations may take place in remote and isolated areas. Gas air compressors provide the necessary compressed air for pneumatic tools, drilling equipment, and other machinery required for these operations.

6. Emergency Preparedness:

Gas air compressors are also beneficial for emergency preparedness in remote locations. In situations where natural disasters or emergencies disrupt the power supply, gas air compressors can provide a reliable source of compressed air for essential equipment and systems. They can power emergency lighting, communication devices, medical equipment, or backup generators, ensuring operational continuity in critical situations.

7. Adaptability to Challenging Environments:

Gas air compressors are designed to withstand various environmental conditions, including extreme temperatures, humidity, dust, and vibrations. This adaptability to challenging environments makes them suitable for use in remote locations, where environmental conditions may be harsh or unpredictable.

Overall, gas air compressors can be effectively used in remote locations due to their independence from the electrical grid, mobility, fuel versatility, on-site power generation capabilities, suitability for off-grid operations, emergency preparedness, and adaptability to challenging environments. These compressors provide a reliable source of compressed air, enabling a wide range of applications in remote settings.

China Professional CHINAMFG Double Acting High Pressure Nitrogen Gas Booster & Compressors Unit   air compressor for saleChina Professional CHINAMFG Double Acting High Pressure Nitrogen Gas Booster & Compressors Unit   air compressor for sale
editor by CX 2024-02-09

Recent Posts